Bombardier CL-604 Lower Wing Plank NPRM: An Inspection Is Only as Good as the Procedure Behind It

The FAA has proposed an airworthiness directive for 201 U.S.-registered Bombardier CL-600-2B16 (604 Variants) airplanes after cracks were found on the lower wing plank at the rear spar and six NDT manual procedures were found that could lead to undetected cracks. Comments are due December 28, 2026.

Most airworthiness directives start with a cracked part. This one starts with a cracked part and then asks a harder question: what if the procedure used to look for that crack could miss it?

On November 10, 2026, the Federal Register published a Federal Aviation Administration notice of proposed rulemaking (NPRM) for certain Bombardier, Inc. Model CL-600-2B16 (604 Variants) airplanes. Comments are open until December 28, 2026.

What prompted the proposal

The NPRM (Federal Register Doc. 2026-22899; Docket No. FAA-2026-13808; Project Identifier MCAI-2024-00785-T; RIN 2120-AA64) follows Transport Canada AD CF-2024-47, dated December 23, 2024. Transport Canada reported cracks found on the lower wing plank at the rear spar, between wing station 59 and wing station 65, in the web and/or flange.

The part of the story that stands out came next. According to the directive, further investigation revealed that six non-destructive testing manual procedures associated with airworthiness limitations tasks could lead to undetected cracks. The FAA states that the unsafe condition, if not addressed, could result in structural failure of the airplane.

The crack was the finding. The procedure was the lesson.

What the FAA is proposing

The FAA proposes to incorporate Transport Canada AD CF-2024-47 by reference and require compliance with it, with only a small number of exceptions. Transport Canada's directive specifies eddy current and ultrasonic inspections for cracks in three areas:

If cracks are found, the directive specifies procedures for repair or rectification. The proposal touches three ATA chapters at once: 53 (Fuselage), 55 (Stabilizers) and 57 (Wings).

Two details are worth noting. Where the Transport Canada AD refers to its own effective date, the FAA version would use the effective date of the FAA AD. And although the referenced material asks for certain information to be submitted to the manufacturer, the FAA proposal does not include that reporting requirement. The FAA also describes the proposal as an interim action, which means further rulemaking could follow if a final action is identified.

The economics

The FAA estimates the proposal would affect 201 airplanes of U.S. registry. Its cost estimate is modest:

The FAA adds that it has no definitive data on which to base cost estimates for any on-condition repairs or rectifications. That is the honest caveat in every crack-finding directive. The inspection has a price. What the inspection finds does not, until it is found.

Why the procedure matters as much as the part

Aviation maintenance runs on trust in written procedures. When an airworthiness limitations task calls for an eddy current or ultrasonic inspection, the technician follows the NDT manual, records the result and signs it off. That signature carries weight because everyone downstream assumes the procedure was capable of finding what it was meant to find.

This proposal challenges that assumption for six specific procedures. That raises a question that goes beyond the cost table. If a procedure could miss a crack, past sign-offs done to that procedure deserve a second look. Not because anyone did the work wrong, but because the work was done to a method that has since been found wanting.

For a business jet fleet like the CL-604, many of these airplanes have changed hands, changed operators and changed maintenance providers over the years. The records that show which procedure revision was used, when, and what was found are not always in one place. The directive tells operators what to inspect going forward. It is up to each operator and maintenance organization to decide what the history tells them.

What good shops already do

Well-run shops will treat this the way they treat any procedure-driven directive. They will read the Transport Canada AD in full, confirm applicability by serial number, schedule the eddy current and ultrasonic work with qualified NDT personnel, and plan access so all three areas can be done in one visit where possible. Many will also pull past records for the affected areas to see which NDT procedure revisions were used and what was recorded. That discipline is what keeps airplanes safe.

Where FLEX AI™ fits, and where it does not

At Platinum Eagle Aerospace we focus on what airframe structures go through between checks, because that history is often thin when engineers and mechanics are asked to make a call on a finding. FLEX AI™ measures strain and temperature today.

It does not detect cracks and does not perform NDT.

We are pursuing an FAA STC for FLEX AI™. Platinum Eagle Aerospace is ISO 9001 certified and is working toward AS9100.

A short checklist for CL-604 operators

When an NDT procedure is revised, how does your team decide how far back to look at past findings? I would like to hear what works in practice.

Source: Federal Register, "Airworthiness Directives; Bombardier, Inc., Airplanes," Doc. 2026-22899, notice of proposed rulemaking published November 10, 2026, comments due December 28, 2026; Transport Canada AD CF-2024-47, dated December 23, 2024. This article summarizes a public regulatory document for general information and is not maintenance or compliance guidance. The proposal may change before a final rule. Always follow the applicable AD and approved manufacturer material.

Learn more about FLEX AI™ structural health monitoring.