A final FAA airworthiness directive for certain Bell Textron Canada Model 429 helicopters shortens the repetitive inspection interval for rivets at the tail rotor gearbox support assembly after numerous failed rivets were found within the existing interval. The AD affects 147 U.S.-registered helicopters and takes effect December 17, 2026.
Inspection intervals are built on an assumption: that a part will not go from acceptable to failed between one look and the next. When that assumption breaks, the interval has to move. That is exactly what has happened with the tail rotor gearbox support rivets on certain Bell 429 helicopters.
On November 12, 2026, the Federal Register published a final airworthiness directive from the Federal Aviation Administration for certain Bell Textron Canada Limited Model 429 helicopters. AD 2026-22-12 (FR Doc. 2026-23007; Docket No. FAA-2026-7227; Project Identifier MCAI-2025-01754-R; Amendment 39-23514) takes effect December 17, 2026. It supersedes AD 2022-20-11.
AD 2022-20-11 already required repetitive inspections at the joint between the tail boom skin and the tail rotor (TR) gearbox support assembly. Operators had to visually inspect the external surface of the support assembly, borescope inspect or visually inspect the inside of the tail boom, and perform a tactile inspection. They were looking for missing or separated rivet tails, rivet tails resting at the bottom of the tail boom, rivet tails not resting against the skin, and gaps between the support assembly and the skin.
The new AD follows Transport Canada AD CF-2025-60R1, dated January 28, 2026. According to the FAA, the Canadian directive states that following reports of numerous failed rivets that were found within the repetitive inspection interval, the manufacturer determined the frequency of repetitive inspections needs to be increased until a terminating action is introduced.
The rivets did not fail between inspections in theory. They failed between inspections in service.
The FAA describes the unsafe condition plainly. Failed rivets and rivets with inadequate grip length, if not addressed, could result in deterioration of the joint structural integrity, detachment of the TR gearbox support assembly, and loss of control of the helicopter.
The final rule requires the same actions as AD 2022-20-11 and reduces the inspection interval. It does this by incorporating Transport Canada AD CF-2025-60R1 by reference, with a small set of exceptions:
The FAA considers the AD an interim action. If final action is later identified, the agency says it might consider further rulemaking.
The FAA estimates the AD affects 147 helicopters of U.S. registry. Each visual, borescope, or tactile inspection is estimated at 1 work-hour at $85 per hour, or $85 per inspection, with no parts cost. Across the U.S. fleet, that is $12,495 per inspection type each time the interval comes around.
On-condition work adds to that. Measuring a gap is estimated at 1 work-hour, or $85. Replacing a rivet is estimated at 1 work-hour plus up to $22 in parts per rivet, up to $9,416 per helicopter. The FAA says it has no way to determine how many helicopters will need repairs, or what an approved gap repair will cost.
None of those numbers is large on its own. What changes is frequency. A shorter interval means the same hour of labor, the same access, and the same aircraft downtime, repeated more often, until a terminating action exists.
The FAA received a single comment on the July 23, 2026 proposal, from an anonymous commenter. That comment asked the FAA to remove the AD's "no reporting requirement" paragraph and require operators to submit inspection data directly to the manufacturer, as the referenced material specifies.
The commenter's reasoning was straightforward. Because the AD is an interim action, a centralized data feedback loop through the manufacturer is essential for deciding whether design changes or permanent terminating actions are necessary. Without structured reporting, neither the manufacturer nor foreign authorities would have full visibility into failure rates across the U.S. fleet.
The FAA disagreed. It is following the state of design, Transport Canada, which did not mandate reporting. The FAA notes that operators may still submit reports, if requested, when accomplishing the service bulletin, but reporting is not mandated for AD compliance. The final rule was adopted as proposed, except for minor editorial changes.
An interim action asks the fleet to keep looking. Whether those findings ever reach the people designing the fix is now largely up to operators.
This AD is a clean example of a pattern we see across rotorcraft and fixed-wing fleets. A joint is inspected on a schedule. Findings accumulate. Some of those findings show up sooner than the schedule expected. The response is a shorter interval, and the long-term answer depends on understanding why the parts are failing when they do.
That understanding comes from data. Every rivet tail found separated, every gap measured, every borescope image logged in a shop is a piece of structural history for that aircraft and that fleet. When reporting is optional, much of that history stays local.
For maintenance teams, there are practical steps worth considering:
At Platinum Eagle Aerospace, our focus is what aircraft structures go through between scheduled checks. FLEX AI™ measures strain and temperature today, building a record of the loads and conditions a structure experiences in service.
We are pursuing an FAA STC for FLEX AI™, and we hold ISO 9001 certification while working toward AS9100. Directives like this one reinforce why structural history matters: the questions regulators and manufacturers ask about a fleet are easier to answer when the data has been captured along the way.
If reporting is optional, does your shop send findings back to the OEM? For a fleet working under an interim action, that answer may shape how quickly a permanent fix arrives.
Source: Federal Register, Vol. 91, No. 217, November 12, 2026, pages 72770 to 72773, FR Doc. 2026-23007, Airworthiness Directives; Bell Textron Canada Limited Helicopters (AD 2026-22-12).
Learn more about FLEX AI™ structural health monitoring.